Automatic Infiltration Meter AIM1
The Automatic Infiltration Meter AIM1 is designed to provide automated logging of infiltration measurements. Infiltration data is one of the key parameters for any planning and agricultural operations, eg determine irrigation scheduling, estimation of run of, design of sprinkler system. It is ideal for researchers, because it saves time.
The Automatic Infiltration Meter AIM1 is stand-alone logger, with an 8GB SD card providing onboard storage for later analysis. Combined with the internal battery, this provides logging options for long term, time efficient monitoring of infiltration. The battery is easily recharged with a 24V power supply (CH24). Communication is via a USB port. The Automatic Infiltration Meter AIM1 is IP-65 rated and has a Windows and Mac compatible Graphical User Interface. With user configurable logging intervals, the user can allocate the time that is required for the soil type under analysis. Examples include 1 second intervals for sandy soil, or minutes for clay soils.
The AIM1 can support up to two Tension Infiltrometers or your own Infiltrometer/Permeameter with installation advice from ICT International.
The AIM1 is ideally used in combination with the volumetric moisture content instrument, the MPKit-406B portable soil moisture kit. For longer term monitoring the Soil Tension Meter (soil water potential) and Soil Moisture Meter (soil water content) are available.
How It Works – Example field installation
- A Tension Infiltrometer is installed in the field and made ready for measurements as per the recommended methodology.
- A differential pressure transducer (CL030) is installed near the bottom of the Infiltrometer and is inserted in the tubing between the top of the water tower and the bottom of the water tower. The use of a differential transducer in this way helps to eliminate the effects of bubble noise in the measurements. Figure 1 is an example of an automated Infiltrometer field setup logging two devices at the same time.
- The pressure transducer is connected to the AIM Automatic Infiltration Meter. The transducer will output a value relative to pressure difference between the air pressure at the top of the water tower and the water pressure at the bottom of the water tower. The pressure value recorded by the transducer is linearly related to a metric value displayed on the Infiltrometer. The AIM converts the pressure value recorded by the CL030 to a metric value.
- The researcher assigns a logging interval in the AIM. For sandy soils logging intervals can be measured in seconds. For clay soils logging intervals can be measured in minutes.
- Figure 2 is an example output data for the CL030 pressure transducer versus time from a Tension Infiltrometer.
- Figure 3 is the data from Figure 2 converted to cumulative infiltration and presented as a function of the square root of time. Output files can record millivolt data, cumulative infiltration data, or both.
- The AIM1 is a fully self-contained unit requiring power input from a solar panel (field applications) or 24V power supply (glasshouse applications).
- All data is stored within the unit on a removable MicroSD card.
- Communication with the AIM1 is made either by USB.
- The AIM1 is compatible with the ICT Combined Instrument Software. The software is GUI based and extremely user-friendly. This software allows complete control of the AIM1 such as real-time measurements, data logging settings, diagnostics and sensor configuration.
- The AIM1 has a 2 wire, non-polarised bus for power supply. There is no chance of incorrect wiring of positive and negative voltage because the AIM1 is non-polarised.
- The AIM1 has an internal lithium polymer battery that is kept charged by an external power supply (solar panel or mains DC power supply).
- The AIM1 is IP-65 rated and has been demonstrated to operate in extreme environmental conditions. Units are being used in diverse environments from hot Australian deserts, tropical Amazon rainforests, temperate German forests, Indian agricultural fields and North American Arctic cold
Tension Infiltrometer TI-20-SS
The SMS tension infiltrometer is designed to add water to soil at a range of tensions, which can be set by the operator of the instrument. By performing infiltration experiments at multiple tensions, one obtains data on the unsaturated hydraulic conductivity at the various tensions.
The range of tensions that can be set is (for practical reasons) limited to tensions between 0 and –30 cm H2O. By setting the tension at or close to zero, one could obtain an infiltration rate that approximates the saturated hydraulic conductivity.
Features:
- On-site determination of hydraulic properties
- Disc can be separated from the water tower or mounted under the water tower
- Requires low volume of water
- Adjustable tension settings
- Flow rates are determined from changes in the water level inside the water tower
- Flow rates can also be determined from changes in the water level recorded with a datalogger, connected to a pressure transducer and attached to the water tower
- Polycarbonate and acrylic materials
- Available with nylon or stainless steel mesh screen membranes
Tension infiltrometers are designed to measure the unsaturated hydraulic properties of soils. Water is allowed to infiltrate soil at a rate, which is slower than when water is ponded on the soil surface. This is accomplished by maintaining a small negative pressure on the water as it moves out of the infiltrometer disc into the soil.
In contrast, the saturated hydraulic conductivity of surface soils is often determined with single or double ring infiltrometers. With single or double ring infiltrometers, water at atmospheric pressure is allowed to infiltrate soil, initially fast, and at a slower rate once the open spaces in the soil fill up with water. When the rate of infiltration has stabilised, the infiltration rate is measured and used to compute the saturated hydraulic conductivity. However, because with ring infiltrometers water is ponded on the soil surface, a good portion of the water might infiltrate through cracks or wormholes, and a reduced amount will infiltrate through the soil matrix. By maintaining a small negative pressure (or tension) on the soil as water is infiltrating, water will not enter the large cracks or wormholes as much, but will infiltrate through the soil matrix. When not all soil pores, cracks and wormholes are filled with water, the soil is considered unsaturated.
Field Set-up
Before placing the infiltrometer on the site where a measurement is to be made, the site is levelled and cleaned of debris. A ring (either 8 or 20 cm in diameter- to be ordered separately from SMS) is placed on the levelled surface. The area within the ring is filled with fine sifted sand from the testing site or with silica sand (a few mm in thickness). The sand is levelled carefully and the ring removed. A perfect flat surface, 8 or 20 cm in diameter, is formed for placement of the infiltrometer. The sand layer should result in good contact between the base of the infiltrometer and the soil below.
For the 20-cm infiltrometer only, make sure the area where the water tower is going to be placed should be at the same elevation as the top of the sand layer for the disc. One can accomplish this by adding or removing soil from this area. It may be convenient to use a carpenters level to make sure these two surfaces are at the same level. Prepare the spot for the water tower using the carpenters level to ensure the correct height of the water tower, before removing the soil ring.
By raising or lowering the tube in the bubble tower, the tension that will be maintained at the bottom of the base plate can be set. The maximum tension is generally less than 30 cm. Many researchers start with the highest tension (often 20 cm). One should note that at the highest tension, the hydraulic conductivity is the lowest, and thus it may take some time for the instrument to start “bubbling”. If it takes too long for bubbles to appear one may want to reduce the initial tension. Some investigators moisten the soil surface with a very fine spray.
Data Collection
The SMS infiltrometers are designed to collect data manually or automatically. Data are collected manually by recording the water level in the supply tower over time. One simply reads the water level in the supply tower at fixed time intervals (i.e. one minute: more frequent early on and less frequent during the steady state phase), and records the information together with the time passed since the start of the experiment.
For multiple sites, it is advantageous to use a datalogger to record the data. The water level in the supply tower is then recorded by installing a 1 psi (66 mbar) differential pressure transducer connected to a suitable datalogger. The pressure difference between the air in the top of the water tower and the water near the bottom of the water tower is recorded. With such a pressure transducer system, the effects of air bubble induced noise are reduced. As the water level in the water tower decreases (as it infiltrates into the soil), the negative pressure in the water tower becomes less negative. Thus, the pressure transducer output is linearly related to the water level in the water tower. Output recorded from the pressure transducer therefore provides a continuous record of the volume of water entering the soil as a function of time. A continuous record with frequent readings is important if one is interested in the early, transient infiltration behaviour.
Water level data can be recorded with a datalogger or similar device. Dataloggers that provide a constant excitation voltage (between 2.5 and 12 volts DC) to the transducer and record the millivolt output from the SMS pressure transducers with an accuracy of at least 0.1 millivolts can be used.
AIM1 Instrument
- Automatic conversion of pressure transducer measurements to cumulative infiltration
- Up to 4 x pressure transducers per AIM
Logging:
- Stand-alone logging
- 8GB MicroSD Removable Storage Card (capacity: 10+ years data storage)
- Simple conversion and scripting
- Flexible sensor calibration, look-up tables, and user scripts
- 24-Bit resolution
- IP65 rated water proof enclosure
- Free Windows utility configuration software
Power management:
- Field: direct connected solar panel
- Lab: mains DC power supply
- Internal Lithium-Polymer battery
- Internal Lithium-Polymer battery charger and power management
- Optical isolation lightning protection
Infiltrometer Specifications |
||
20cm Model | 8cm Model | |
Specifications | US Patent No. 4884436 | US Patent No. 4884436 |
Diameter Disk | 20cm | 8cm |
Inside Diameter Water Reservoir | 5.1cm | 2.54cm |
Inside Diameter Bubbling Tower | 2.54cm | 2.54cm |
Length Water Reservoir | 81cm | 81cm |
Bubbling Pressure Membrane | 30cm H2O | 30cm H2O |
Carrying Case Dimensions (optional) | 28cm x 36cm x 107cm | 28cm x 36cm x107cm |
Pressure Transducer | 1 psi (67cm H2O) | 1 psi (67cm H2O) |
Instrument Logging |
|
Analogue Channels | 5 differential |
Resolution | 0.00001V—24-Bit |
Accuracy | 0.001V |
Minimum Logging Interval | 1 second |
Delayed Start | Suspend Logging, Customised Intervals |
Sampling Frequency | 10Hz |
Communications | USB, Wireless Radio Frequency 2.4 GHz |
Data Storage | MicroSD Card, SD, SDHC & SDXC Compatible (FAT32 format) |
Software Compatibility | Windows 8, 8.1 & 10. Mac OS X. |
Data Compatibility | FAT32 compatible for direct exchange of SD card with any Windows PC |
Data File Format | Comma Separated Values (CSV) for compatibility with all software programs |
Memory Capacity | Up to 16GB, 4GB MicroSD card included. |
Temperature Range | -40°C to +80°C |
R/H Range | 0-100% |
Upgradeable | User Upgradeable firmware using USB boot strap loader function |
POWER |
|||
Internal Battery Specifications | |||
960mAh Lithium Polymer, 4.20 Volts fully charged | |||
External Power Requirements | |||
Bus Power | 8-30 Volts DC, non-polarised, current draw is 190mA maximum at 17 volts per logger | ||
USB Power | 5 Volts DC | ||
Internal Charge Rate | |||
Bus Power | 60mA – 200mA Variable internal charge rate, maximum charge rate of 200mA active when the external voltage rises above 16 Volts DC | ||
USB Power | 100mA fixed charge rate | ||
Internal Power Management | |||
Fully Charged Battery | 4.20 Volts | ||
Low Power Mode | 3.60 Volts – Instrument ceases to take measurements | ||
Discharged Battery | 2.90 Volts – Instrument automatically switches off at and below this voltage when no external power connected. | ||
Battery Life varies | |||
|
TENSION INFILTROMETER TI-20-SS
TENSION INFILTROMETER SPECIFICATIONS |
20 cm Model |
8 cm Model |
Diameter Disc |
20 cm |
8 cm |
Inside Diameter Water Reservoir |
5.1 cm |
2.54 cm |
Inside Diameter Bubbling Tower |
2.54 cm |
2.54 cm |
Length Water Reservoir |
81 cm |
81 cm |
Bubbling Pressure Membrane |
30 cm H2O |
30 cm H2O |
Carrying Case Dimensions(optional) |
28cm x 36cm x 107cm |
28cm x 36cm x 107cm |
Pressure Transducer |
1 psi (67 cm H2O) |
1 psi (67 cm H2O) |